Girsan MC P35 Pro IDPA Competition Rig
Free US shipping. Same-day dispatch before 2 PM EST.
A Pro IDPA Competition Rig for the Girsan MC P35: a Pro IDPA Competition Holster, a cut-to-fit Tactical Gun Belt and two IDPA mag pouches. Right-hand draw only.
What's included
- (1) Pro IDPA Competition Holster for the Girsan MC P35, in black
- (1) Tactical Gun Belt 1.5'' in black, with belt keeper and a 2mm Allen key
- (2) IDPA Double Stack Competition Magazine Pouches in black, already sized for your magazines
Holster
A 0.088'' Kydex shell molded for the Girsan MC P35. Optics ready, and the muzzle end leaves room for a threaded barrel. Phillips screws on the shell set the retention.
The belt attachment is a clip: press the two buttons on each side and it opens. Two plastic tabs inside pull off and press back on to fit belts from 1.5'' to 2'' wide.
Belt
A 1.5'' wide, 0.25'' thick nylon belt with a reinforced core, 48'' long. It's one length: you cut it to fit at the buckle end, then the ratcheting buckle adjusts in 1/4'' steps across 40 positions. Read the Belt sizing section before you cut.
Magazine pouches
Kydex pouches sized for your pistol's magazines, with a neutral ride height. Phillips screws set the retention. They clip onto the belt with the same attachment as the holster.
Setup takes the included 2mm Allen key for the belt buckle and a Phillips screwdriver (not included) for the retention screws.
Made for IDPA competition.
Made in the USA.
The belt comes 48'' long and you cut it to your size once, at the buckle end. Measure twice, cut once: you can always take off more, but you can't put it back.
- Find your cut length. Take your pant size and add 4'' if you carry outside the waistband (like the Pro IDPA Competition Rig), or 6'' if you carry inside the waistband. Example: 34'' pants, outside the waistband, cut length 38''.
- Mark the belt. Lay the belt flat. Measure from the tip (the end without the buckle) and mark your cut length. Measure again before you cut. If your cut length comes close to the full 48'', don't cut yet: try the belt on first.
- Take off the buckle. With the included 2mm Allen key, loosen the two screws on the buckle. Raise the clasp on the bottom of the buckle and slide the belt out.
- Cut. Cut straight across at your mark with sharp scissors or a knife.
- Put the buckle back on. Insert the cut end into the buckle, press the clasp down firmly so its teeth grip the belt, then tighten both screws with the 2mm Allen key until snug. Don't overtighten, or the screws can strip.
- Try it on. Thread the tip through your pant loops and into the buckle, and click it until snug. The buckle adjusts in 1/4'' steps across 40 positions. The tip should reach about 3'' past your first belt loop. Still too long? Take the buckle off and trim a little at a time. Tuck the extra into the belt keeper.
The rig comes assembled with the holster and mag pouches matched to your pistol. Size the belt first (see "Belt sizing"), then set up the gear.
- Size the belt. Measure twice, cut once, following the Belt sizing steps.
- Set the attachments to your belt. The holster and both mag pouches use the same clip. Press the two buttons on each side to open it. Pull off the two plastic tabs inside and press them back on in the position that fits your belt (the Tactical Gun Belt is 1.5'').
- Lock the attachment screws. Put a drop of removable (medium strength) thread locker on the screws that hold the belt attachment to the holster and to each mag pouch, so they stay tight. Don't use a permanent thread locker, because it can seize the screws.
- Clip on the gear. Close each clip over the belt until it locks. Put the holster on your right hip and the two mag pouches on the side opposite your holster. Check the current IDPA rulebook for holster and pouch placement before a match.
- Set the retention. With an unloaded pistol and empty magazines, turn the Phillips retention screws on the holster and on each pouch. Tighter holds more securely while you move. Looser lets the pistol or magazine come out with less effort.
- Check it. Make sure every clip is closed and locked, and recheck the screws before each match.
Tools
- 2mm Allen key: belt buckle screws (included)
- Phillips screwdriver: holster and pouch retention screws (not included)
- Removable (medium strength) thread locker (not included)
Choose options
Ran flawlessly during my 5.5 mile run and gun. No screws backed out. It just runs like it’s supposed to. I honestly couldn’t ask for anything more than this. And I highly recommend your equipment to anyone else looking to compete or train
My wife and I just started shooting USPSA and IDPA. We bought (2) of these for us to compete. Would recommend to any one looking for a complete setup.
When I changed IDPA divisions and pistols (SSP to CO and G34 to Walther PDP), I needed a new rig since the other manufacturer did have a fit for the PDP Compact. I did a lot of research and decided to give Black Scorpion a try. I have NOT been disappointed! The construction and especially the secure clip on/off nature of the components is top shelf. I especially like the belt’s construction as it mirrors the previous one I’d been using but I like the buckle clasp and fit better than my previous rig. Match performance has been stellar this far. Keep up the great work!
This Belt is everything's you expecting. Good quality, excellent fabric. Very protectional. Works Amazing. The price is words it. 100 % recommended.
New to the competitive shooting game but look forward to using this gear this weekend. Seems very well made, holster and mag holders are stable. Did a lot of research before choosing Black Scorpion and so far glad I did.
Super stiff outer belt it’s great everything stays exactly where I need it too worth the money also if you’re a size 34 pant get the xl belt
Bulky af on the over lap that or I got to big of a size
Very good !
The hardware and screws holding everything are stripping out with adjustments and i can’t tension them or loosen them now
First belt works great mag pouch are great
High quality does what it should
Just shot my first IDPA match and the product worked great
Walther PDP 4.5'' Pro Competition Rig
Competition Rig - 1 Heavy Duty Belt w/ 4 Ambidextrous Single/Double Stack Magazine Pouches
Great quality, fits my Beretta 92X PCO perfectly.
Magazines fit nicely too
Works great good price
The screws for the magazine carriers constantly come loose, probably will use locktite, but shouldn't have to.
Never received the order; contacted them
They held me accountable for the carrier's fault and will not reship the replacement or refund
I am stuck with my money and no product
The kit is fine, works great. For the love, make a video demonstrating how to attach the mag pouches and holster to the belt, not being able to properly assemble the belt system out of the box was very frustrating. Also include the tools to work the systems in the bag, having to search my garage for 6 alan keys wasn't fun either, not to mention the fact that almost every screw was a different size.
!
Great strap. But just a tad short. Cant make it any longer. Elastic at one end helps but If you have bigger thighs may be a bit tight.
You want review on an order I haven’t received?
This belt is fantastic and I’m already looking at incorporating some mag holders for my work belt in addition to what carry on my vest
I think the belt and holster will do well, not so sure about the mag pouches. They don’t seem to be fitted for the 2011 magazines. My Glock 34 magazines fit perfectly, but that’s not what I was needing. Will let you know how they perform after shooting a match.
Awesome Rig
The drop belt attachment fits my padded belt fine, so I like it for longer matches where weight can wear on the hips. I use it with the Scorpion quick release OWB holster which provides sufficient offset to allow going to the grip easy.
Purchased holster, belts, and mag holders. Great product, nice fit, solid construction. Have not had a chance to shoot competitively yet but has been outstanding while running practice drills.
For context, I compete occasionally in 2-gun, 3-gun, and other "non-lettered" local competitions. I generally avoid USPSA and IDPA, except occasionally. If the rules do not prohibit drop leg holsters, I use the Black Scorpion quick detachment drop leg holster with two leg straps. For me, it's the most stable and comfortable. If the competition rules state that the pistol's grip cannot be below the belt line, I use this duty drop leg belt attachment. I find it provides the same stability and comfort with only one leg strap. The only difference is that my hand/wrist consistently hits my pistol with the belt attachment. The full drop leg holster setup is a couple inches lower. I have them both from Black Scorpion, and one male attachment for my holster that can easily go back and forth between the two belt or leg rigs. This is perfect for me.